Fiat 500 Replacement Key Fob
It could be time to replace the battery if your 500 remote key fob is not working. If you replace the battery but it doesn’t work the issue could be somewhere else.
United Locksmith specializes in the production of new keys for classic automobiles. We have the tools and spare parts needed for this job.
Dead Coin Battery
The most frequent reason why your fiat Multipla key 500 key fob will not lock or unlock the doors is due to a dead battery. The key fob is equipped with a coin cell battery that will drain quickly when it isn’t being frequently used. If your remote has started to show signs of a loss of range or stopped functioning, then the battery may be dead.
The battery inside the key fob is held in place by metal clips that hold it in place. If the clips aren’t secure, they can cause contact issues, which could prevent the remote from receiving power. Use a flathead screwdriver to pry open the retaining clip and remove the battery. Make sure to select an alternative battery that has the same kind of voltage, size, and specification as the original battery.
Exposure to water can cause the key fob to become corroded or damaged. Even a short bath in soapy, Fiat 500 car key warm water can cause damage to the chip. It is best to keep your key fob in a dry environment.
Water Damage
If your key fob doesn’t work properly, it could be due to water damage. Key fobs are fitted with rubber seals that stop them from being damaged by light rain or splashes of water, however it is essential to keep your car keys from being tossed into the pool, ocean and washing machine!
The key fob comes with an electronic chip that transmits a signal car’s immobilizer system. The chip is what allows the 500 to lock and start. If it gets wet, it will no longer work.
Try cleaning the inside electronics of your keyfob with isopropyl Alcohol or an electronic cleaner to determine whether they’re still in good condition. It is best to replace a key fob in the event that it has been submerged into salt water rather than try to repair it yourself.
Although a replacement fob may cost a little money, it is far less expensive than paying for your Fiat 500 to be towed to the dealer and repaired! You can also do it yourself with just a few steps. Be sure to have the correct battery type prior to opening your keyfob. There are step-by-step directions for every car keyfob online.
Faulty Chip
The chip in the key fob communicates directly with the immobiliser of your car to ensure that your vehicle will only start when the correct keys are inserted. If the chip is damaged or corrupted it won’t allow your car to start regardless of what you do.
A chip that is defective can happen due to a variety of reasons but most commonly due to water damage or the battery being dead. It is best to leave the job to a professional locksmith who can replace the chip quickly and at an affordable cost.
If your key fob will not function after exposure to water that is clean from the tap or rain take it off the battery. Clean the electronic component using paper towels. If the key fob does not work, there is the possibility that it’s damaged components and requires to be replaced.
Some people go to their dealer when they require an entirely new Fiat fob. However, this can be expensive. United Locksmith is the best option if you want your Fiat keyfob repaired at a reasonable cost. We have all the equipment and know-how to repair your fiat van key replacement fob in a professional and timely manner.
Faulty Receiver Module
Fiat key fobs transmit an electrical signal to the vehicle that can unlock and close doors (and start the car for those with an automatic transmission) up to 50 feet. However there are several things that could cause the fob to cease working. This could be due to a dead coin battery or water damage, worn buttons or a problem with the receiver module and signal interference, or an electronic chip that is malfunctioning.
If the fob was located in the pocket of someone who has suffered severe trauma (such as being dropped on the floor, or washed in a washing machine) it might not be able to communicate with the Body Control Module (BCM) of the car. This is because the BCM is secured and will only accept a signal from a genuine key and not accept any other.
You’ll have to replace the fob if this happens. A professional locksmith can handle every aspect of the key replacement procedure and can even program a brand new one for your 500. They can even provide an clone fob that performs the same as the original (and costs just less than the price).